THE NUMERICAL STUDY OF EXTRUSION PROCESSES POLYMER MATERIALS UNDER VARIOUS HEAT EXCHANGE CONDITIONS ON THE SCREW
- Authors: Puzanov M.V1, Subbotin E.V1
- Affiliations:
- Perm National Research Polytechnic University
- Issue: No 2 (2014)
- Pages: 20-28
- Section: Articles
- URL: https://ered.pstu.ru/index.php/elinf/article/view/2764
- DOI: https://doi.org/10.15593/вестник%20пермского%20национального%20исследовательского%20политехнического%20университета.%20электротехника,%20информационные%20технологии,%20системы%20управления.v0i2.2764
- Cite item
Abstract
The process of flow and melting of polymer materials in the extruder screw channel taking into account the thermal conductivity of screw was considered. The multilevel algorithm of iterative procedures for joint solving tasks of heat and mass transfer of polymers under conditions of phase transition in the working channel of extrusion equipment and determination of the temperature field of screw was proposed Carried out the numerical study of the influence of heat transfer in screw on the processing of insulating polymeric mediums by extrusion by comparison of the results obtained by using in the calculations of various heat exchange conditions on the screw. Shows graphs of changes along the length of the extruder channel of the screw temperature, the cross section area of solid bed, the average temperature of polymer. The pressure-flow characteristics of extruder were built. The recommendations for use in mathematical models of various heat exchange conditions on the screw were given.
About the authors
M. V Puzanov
Perm National Research Polytechnic University
Email: ktei@pstu.ru
E. V Subbotin
Perm National Research Polytechnic University
Email: ktei@pstu.ru
References
- Тадмор З., Гогос К. Теоретические основы переработки полимеров. - М.: Химия, 1984. - 632 с.
- Басов Н.И., Брой В. Техника переработки пластмасс. - М.: Химия, 1985. - 528 с.
- Раувендаль К. Экструзия полимеров. - СПб.: Профессия, 2008. - 786 с.
- Chung C.I. A new theory for single-screw extrusion // Modern. Plast. - 1968. - № 9. - P. 178-198.
- Syrjälä S. On the analysis of fluid flow and heat transfer in the melt conveying section of a single-screw extruder // Numer. Heat Transfer. Part A. - 1999. - Vol. 35, № 1. - P. 25-47.
- Lin P., Jaluria Y. Conjugate Thermal Transport in the Channel of an Extruder for Non-Newtonian Materials // Int. J. Heat Mass Transfer. - 1998. - Vol. 41. - P. 3239-3253.
- He H., Zhou J. Simulation of cottonseed cake melt flow in metering zone of a single screw extruder // Front. Chem. Eng. China. - 2010. - № 4(3). - P. 263-269.
- Щербинин А.Г., Труфанова Н.М., Янков В.И. Пространственная математическая модель одночервячного пластицирующего экструдера. Сообщ. 1. Математическая модель процесса тепломассопереноса полимера в канале экструдера // Пластические массы. - 2004. - № 6. - С. 38-41.
- Самарский А.А. Теория разностных схем. - М.: Наука, 1972. - 656 с.
- Elbirli B., Lind J.T. Mathematical modeling of melting of polymers in single-screw extruder // Polymer Eng. Sci. - 1984. - Vol. 24, № 12. - P. 988-999.
- Лина В., Чамов А.В. Экструзия полимеров, не поддерживающих горение // Кабели и провода. - 2003. - № 6(283). - С. 16-20.
Statistics
Views
Abstract - 57
PDF (Russian) - 39
Refbacks
- There are currently no refbacks.
